The watch winder can also be powered via the USB power plug (optional). Watches because their winding mechanism is different from the traditional automatic watch movement.Ģ. Watch winders are not compatible with Seiko Kinetic
#AUTOMATIC WATCH WINDER CASE MANUAL#
If your watch allows for manual winding only, this watch winder will not be able to wind it. Please keep the door of the watch winder closed for its proper operation. PLEASE NOTE: The rotors will not rotate if the Motor-Stop option is enabled and the door stays open. To enable this option, flip the small black switch on the back panel to the ON position (optional). If the Motor-Stop option is enabled,Īll the rotors will stop once you open the door. To prevent the winding mechanism from breakdowns, it is recommended to put a watch into a rotor or take it out only when the rotor is stopped. The light can also be controlled by the red switch on the rear panel (optional). Press to turn the interior light ON or OFF. Use to set the hour, button to set the minute and to save the settings. Press and hold for 2 seconds until the control panel vibrates. If you have set a bi-directional mode, the rotor will rotate clockwise for 2 hoursĪnd counterclockwise for another 2 hours. Then the rotor will rest for 8 hours and return to the programmed winding mode. It will rotate the watch for 4 hours continuously. The Turns-Per-Day display will show and the selected rotor will start moving. Press and hold the TPD display area for 2 seconds. Then press to activate the program (the display must show inģ. Set the required TPD and rotation direction by pressing, and. Mount the watch and choose the rotor by pressing and. To activate this mode, please proceed as follows:ġ. This mode is intended for winding new or stopped watches. The display will show in the Rotor Selection Section and the selected rotor will not move until you reactivate it.Īctive rotors are always indicated by an underline under their numbers. Press and several times to select a rotor.Ģ. It is recommended to deactivate the rotors you do not use.ġ. The rotors do not rotate continuously and stay motionless most of the time. PLEASE NOTE: The winding controller splits the programmed number of turns per day in 24 hours evenly. If Motor-Stop option is enabled, the rotation will start after you close the door. The display will show in the Rotor Selection section and the selected rotor will start moving.
Select the winding direction for your watch by pressing. Having selected a rotor to program, select the number of Turns-Per-Day (TPD) by pressing and. The selected rotor will be shown in the Rotor Selection Section on the display.Ģ. Use and buttons to select a setting target. Please check the user manual of the watch or contact the customer service of your watch brand for detailed information.Įach rotor can be programmed independently.ġ. The watch winding mode (the winding direction and the Turns-Per-Day setting) depends on the watch model. You can also refer to our watch winding parameters table. Please, check your owner's manual or contact your watch brand's customer service for detailed information. Please note: Watch winding mode (winding direction and TPD setting) depends on your watch model. The watches shown in the pictures are not included. Watch winders are not compatible with Seiko Kinetic Watches because their watch mechanism is different from the traditional one. Please note: If your watch doesn't wind itself from wrist motion, it cannot be wound by an automatic watch winder. With an automatic watch winder, you can keep your timepiece wound and ready to go!
If it has additional functions (like date, moon-phase display, perpetual calendar), resetting them may take a lot of time and require certain skills. When your timepiece stops, you must reset time and wind up your watch.
The reserve depends on the watch brand and on movement (caliber) used. Automatic watches have a limited power reserve, so if you stop wearing them and winding them up, they will run down in two or three days.
Product weight: 13.2 lbs (6 kg) What is an automatic watch winder?Ī watch winder is a device with an electrical motor which will automatically wind your watch when you are not wearing it. Product dimensions (W x L x H): 9" x 10" x 13" (23 cm x 26 cm x 33 cm) 4 Individually programmed winder rotors.
#AUTOMATIC WATCH WINDER CASE INSTALL#
This option prevents the breakdown of the winder mechanism when you install or remove the watch.Īll rotors stop at the same position after each winding cycle for a better display of your watch collection. If Motor-Stop option is activated, all rotors will stop when you open the door. The watch winder has a Motor-Stop option. Maximum watch case diameter: 2.4 inches (60 mm) Automatic Watch Winder with LCD Touchscreen Control, Interior Light and Coordinated Rotor Stop PositionĮxterior finish: High-gloss piano lacquer
0 kommentar(er)
